PRODUCT
Overview
DC Power Supplies
Battery Chargers
DC-DC Converters
PV Charge Controllers
Misc. Products & Accessories
SUPPORT
Driver download
Document download
Product Video
FAQ
DISTRIBUTOR
Middle East and Africa
ABOUT US
Overview
Company Statement
Quality Assurance
Green Manufacturing
OEM & ODM and Contract
News

12V to 12V 110A in-car charger for Lead and LFP batteries

SBC-6111
Feature
Model
SBC-6102 SBC-6104 SBC-6106 SBC-6111
12V, 23A 12V, 40A 12V, 60A 12V, 110A

High efficiency 110A charger

3 Power Up Control Mode : Auto-Ignition Feed ,Built-in Vibration Sensor & Input Voltage Control.

Designed for Euro 5/6, smart alternator & conventional ones.

6 Battery type selections : 2 of Each in AGM/LEAD/LFP

3 Stage charge for Lead based & a specific 2 Stage for LFP

Add to compare list
Compare
Search
Compare

Optimal Efficiency 92% with Digital Control
The high power conversion efficiency allows quiet and cooling running of the charger and can provide continuous full load
operation at 40°C ambient temperature. 

Designed to cover old and new types of car alternators
The SBC-6111 are designed to address to the issues of wide swing of output voltages from the smart alternator, braking regenerative EURO 5/6 vehicles in fully charging the house battery. They are also suitable for use with distant house battery. The charger Booster provides fast safe charging profiles for 4 types of lead based and 2 types of Lithium FePO4 batteries.

Multistage Charging
This is a select (battery type) and forget charger designed for fast accurate and safe recharge of your deep cycle house battery banks. The (digital control) smart multistage charging enables the charger to be connected permanently to your battery banks without the worry of over charging or drying out the electrolyte.

Lead acid based Battery
A 3 Stage Bulk, Absorption & Float charging profile for 4 types of lead acid based battery with maximum constant charging current at the Bulk Stage and a Constant Voltage with decreasing charging at the Absorption Stage and a reduced voltage Float Charge for maintenance when battery is full.

LiFePO4 (LFP) Battery
A 2 Stage charging is specially for 2 types LiFePO4 battery and charging current stops at the end of Absorption stage. 

Three charge control methods:

Ignition Control: Charger starts charging only when ignition is on and stops charging when Ignition is off.
This is the recommended control as it is safer and allows for large input voltage range.

Input Voltage Control: This is for non-intelligent or older type alternators with sufficient high & uniform voltage.
Charging is cut off easily due to high threshold voltage to protect the starting battery.

Vibration Sensor Control: Charger starts charging when repeated vibrations are detected and stops charging when no vibration is detected for over 2 minutes.
The built-in vibration sensor makes it possible to use the charger by just connecting to the starter terminal without touching the car’s electrical/electronic wiring thus avoiding any possible excuse for revoking the car’s warranty.

Features

  • 1600Watt power conversion efficiency >90%.
  • 6 selective charging profiles suitable for charging for the most lead acid & Lithium FePO4 batteries.
  • Supplied with a remote Battery temperature sensor to ensure precise and safe charging in large temperature variation.
  • 3 types of operation control to choose for specific situation.
  • Alarm signal (fault or not charging) available to integrate with your system.
  • Thermostatically speed control Fan.
  • Protections:
    • Self recoverable Input under Voltage protection.
    • Self recoverable Input over Voltage protection.
    • Self recoverable Output over Voltage protection.
    • Self recoverable Overcurrent protection.
    • Self recoverable Charger over temperature protection.

Remote battery temperature sensor
Bundled remote battery temperature sensor allow the charger monitor battery temperature and automatically compensate the charging voltage according to battery temperature. It protect the battery by cut off output of charging whenever battery temperature are too high or drop below -10°C.

Optional remote control SDR-5100
SDR-5100 remote control is remote panel for Manson chargers. It can be used to monitor charger status and configure the charger. It come with a 4m length cable for you to connect the charger to the car panel.  In additional to monitoring and configure the charger, SDR-5100 enable two user define setting for SBC-6111. You can set two customized charging profiles for your battery.

Input Voltage
9-16VDC
PV input
N/A
Output Voltage
Max 15V
Max charging current
110A
Recommend Max battery size
100-380AH
Efficiency
92% (Optimal)
Support battery types
LEAD, LEAD Type 2, AGM, AGM Type 2 LiFePO4, LiFePO4 Type 2
User define battery type
Enable through optional remote control (SDR-5100)
Power supply mode
Not applicable
Number of output
1
Number of charging stage
3 stage for LEAD and AGM, 2 stage for LiFePO4
Equalization
Enable through optional remote control (SDR-5100)
Soft-start
Yes
standby mode
No
Display
LED indicators
Minimum Battery Voltage
5V
Protection
Input & Output reverse polarity protection, Input Under Voltage protection, Output Over Voltage protection, Over Load, Charger Over Temperature.
Cooling Method
Thermostatically speed control Fan
Remote Battery temp. sensor
Yes
Accessories
Mounting screw, User manual
WiFi Connection
Optional factory preinstall Bluetooth
Operation Temperature
-10°C to +50°C (Full load at +40°C)
Approvals
CE compliance
Dimensions
268x130x73 mm
Weight
1.8kg
Document
SBC-6104/ 6106/ 6111 User Manual
Rev.4
English
11/06/2024
SBC-6104/ 6106/ 6111 User Manual
SBC-6000 Series catalogue
Rev.1
English
04/10/2023
SBC-6000 Series catalogue
Video
Language

Warning: Invalid argument supplied for foreach() in /home/manson7/public_html/wp-content/themes/odf-theme/template/content/single-products.php on line 465
FOLLOW US